Do you know the Proximity Sensor E2A-M18KS08-WP-B1 price in bd? OmronModel Number Legend Example: E2A-M12LS04-M1-B1 Standard, M12, long barrel, shielded, Sn=4 mm, M12 connector, PNP-NO E2A-M08KN04-WP-B1 5M, Standard, M8, short barrel, non-shielded, Sn=4 mm, pre-wired PVC cable, PNP-NO, cable length=5 m

Technical Data Proximity Sensor
DC 3-wire Models
Size TypeItem |
M8 | M12 | |||
Shielded | Non-shielded | Shielded | Non-shielded | ||
E2A-M08@S02-M1-B1 E2A-M08@S02-M1-B2 E2A-M08@S02-M1-C1 E2A-M08@S02-M1-C2 E2A-S08@S02-@@-B1 E2A-S08@S02-@@-B2 E2A-S08@S02-@@-C1 E2A-S08@S02-@@-C2 |
E2A-M08@N04-M1-B1 E2A-M08@N04-M1-B2 E2A-M08@N04-M1-C1 E2A-M08@N04-M1-C2 E2A-S08@N04-@@-B1 E2A-S08@N04-@@-B2 E2A-S08@N04-@@-C1 E2A-S08@N04-@@-C2 |
E2A-M12@S04-@@-B1 E2A-M12@S04-@@-B2 E2A-M12@S04-@@-C1 E2A-M12@S04-@@-C2 |
E2A-M12@N08-@@-B1 E2A-M12@N08-@@-B2 E2A-M12@N08-@@-C1 E2A-M12@N08-@@-C2
|
||
Sensing distance | 2 mm ± 10% | 4 mm ± 10% | 4 mm ± 10% | 8 mm ± 10% | |
Setting distance | 0 to 1.6 mm | 0 to 3.2 mm | 0 to 3.2 mm | 0 to 6.4 mm | |
Differential travel |
10% max. of sensing distance | ||||
Target | Ferrous metal (The sensing distance decreases with non-ferrous metal.) | ||||
Standard target (mild steel ST37) | 8´8´1 mm | 12´12´1 mm | 12´12´1 mm | 24´24´1 mm | |
Response frequency (See note 1.) | 1,500 Hz | 1,000 Hz | 1,000 Hz | 800 Hz | |
Power supply voltage (operating voltage range) | 12 to 24 VDC. Ripple (p-p): 10% max. (10 to 32 VDC) |
||||
Current consumption (DC 3-wire) |
10 mA max. | ||||
Output type | -B models: PNP open collector -C models: NPN open collector |
||||
Control output
|
Load current (See note 2.) | 200 mA max. (32 VDC max.) | |||
Residual voltage | 2 V max. (under load current of 200 mA with cable length of 2 m) | ||||
Indicator | Operation indicator (Yellow LED) | ||||
Operation mode (with sensing object approaching) |
-B1/-C1 models: NO -B2/-C2 models: NC For details, refer to the timing charts. |
||||
Protection circuit | Power source circuit reverse polarity protection, Surge suppressor, Short-circuit protection | Output reverse polarity protection, Power source circuit reverse polarity protection, Surge suppres- sor, Short-circuit protection | |||
Ambient air temperature | Operating: -40°C to 70°C, Storage: -40°C to 85°C (with no icing or condensation) | ||||
Temperature influence (See note 2.) | ±10% max. of sensing distance at 23°C within temperature range of -25°C to 70°C ±15% max. of sensing distance at 23°C within temperature range of -40°C to 70°C |
||||
Ambient humidity | Operating: 35% to 95%, Storage: 35% to 95% | ||||
Voltage influence |
±1% max. of sensing distance in rated voltage range ±15% | ||||
Insulation resistance | 50 MW min. (at 500 VDC) between current carry parts and case | ||||
Dielectric strength | 1,000 VAC at 50/60 Hz for 1 min between current carry parts and case | ||||
Vibration resistance | 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y and Z directions | ||||
Shock resistance | 500 m/s2, 10 times each in X, Y and Z directions | 1,000 m/s2, 10 times each in X, Y and Z directions | |||
Standard and listings (See note 3.) | IEC60529: IP67, Degree of protection EN60947-5-2: EMC | ||||
Connection method | -WP models: Pre-wired models (Standard length: 2 m) -M1 models: M12 4-pin connector models -M5 models: M8 3-pin connector models |
||||
Weight (packaged)
|
Pre-wired model | Approx. 65 g | Approx. 85 g | ||
M12 connector model | M12 connector models: Approx. 20 g M8 connector models: Approx. 15 g | Approx. 35 g | |||
Material
|
Case | Stainless steel or brass-nickel plated | Brass-nickel plated | ||
Sensing surface | PBT | ||||
Cable | PVC | ||||
Clamping nut | Brass-nickel plated |
More About Proximity Sensor E2A-M18KS08-WP-B1 price in bd
Power Reset Time The Proximity Sensor is ready to operate within 100 ms after power is supplied. If power supplies are connected to the Proximity Sensor and load respectively, be sure to supply power to the Proximity Sensor before supplying power to the load. Power OFF The Proximity Sensor may output a pulse signal when it is turned OFF. Therefore, it is recommended that the load be turned OFF before turning OFF the Proximity Sensor. Power Supply Transformer When using a DC power supply, make sure that the DC power supply has an insulated transformer. Do not use a DC power supply with an auto-transformer. Mutual Interference. When installing two or more Sensors face-to-face or side-by-side, ensure that the minimum distances given in the following table are maintained. For More Information Please Contact BD Engineering Solution
Our Other Product:
Proximity Sensors Omron E2E2-X5C1 29 mm 12 to 24 VDC
BI2-M12-AP6X-H1141 | Proximity Sensor TURCK
SICK GTB6-P1212-Photoelectric proximity sensor PNP-NPN
Capacitive, Proximity, Photo Sensor LJC30A3-20-Z/BY